* This text has been translated from Russian to English
Replacing belt on GRM SUZUKI baleno G16B-this technology does not discharge refrigerant and does not remove the air conditioner compressor, and not to remove the pump and the right-Gura pillow engine.
Removing the belt GRM:
1) Disconnect the negative battery terminal.
2) Put protivootkatnye shoes for the rear wheels. Post right front wheel jacks and put further emphasis, security, first and foremost.
3) Remove the right front bottom of a plastic protective sleeve. (Screwdriver and Key frontal at 10.)
4) Remove the casing with air filter.
(Screwdriver and Key frontal at 10.)
5) Otkrutite the bar between the engine and 2 pillow bolt.
(Hexagon 6)
6) Otkrutite two screws fastening the oil probe and take him to be more convenient twist off the belt SRM casing (key 10).
7) Otkrutite jacket belt 10 bolts and the center of the enclosure above the middle nut key 10 (key to the 10 carob and накидной thin, if not thin cut on the emery)
8 ) It is desirable to cut down this nut with stud spare no if this is not done, you can break the casing. I have a problem, went nut with stud, and not backwards not forwards and back saw had cut down the canvas. (Spilennoy instead of nuts in the future, set screw attachment to the windscreen wipers WHA so without our spare parts can not do.) And also cut down fly installation of ignition, it is not will pull the sleeve up the hole formed after спила can fly zakleit. I used a piece of spilennoy fly cut it to the abrasive and glued into placeusing soldering iron. Yes, and I cut down a fly using soldering iron cut long, and not convenient.
9) Otkrutite bolts pump, without removing the belt. (Key to 10.)
|
|
10) including 5-nd transfer otkrutite and bolts ratchet 5 pcs. (Head turned to the 8 or if there is a fine).
11) Remove the belt and the air conditioner Gura while releasing tension roller. (Key накидной 12 * 14).
12) Remove the generator belt.
13) It is desirable to guard belt GRM was warm. You can use the industry. hair dryer, if not, get out of the wife or girlfriend and a good running jacket. Hold the hair dryer for warming the hands and in those places where it will stick sleeve.
14) The operation to remove a jacket is better to make two, one pulls the other corrects. Pull up and a little on himself.
15) After the withdrawal of the enclosure expose thong GRM label (see below). Tripwires movie release bolt, stud arc spot and unhook spring, remove the belt.
(Накидной key 12 * 10)
16) Zataskivanie manufacture and installation of casing in reverse order.
17) It is desirable when assembling a torque wrench. The Japanese ruchonki small compounds and require tightening with a certain point!
Install the belt on GRM SUZUKI BALENO G16B
2.1) Inspect idler roller, scroll through his hands, if not postorennego noise and play, put it back into place, and if I had bought, I am, but not the original expectations low.
2.2) Tag «E» to a point on the pinion shaft distribution should coincide with the slot on the valve cover and should be placed at an angle of 90 degrees to the upper valve cover. (No confusion there is another label but without the «E»)
i) Slot
ii) «E» to a point.Top
2.3) at the bottom of the crankshaft is the same, the label on the gear drive belt SRM set vertically up and combine with the arrow on the block.
2.4) The moments of tightening bolts:
Bolt tripwires roller 2.5 kg * m
Bolt tripwires arc spot 1,1 kg * m
Bolts jacket belt 1,1 kg * m
Bolts ratchet 1.6 kg * m
Bolts pump pulley 1.1 kg * m
2.5) After the tension of the belt of the free portion (from where there is no traction roller) must sweep of the hand at an angle of 45 degrees.
This is important not drag Belt !!!!.
